Ivoclar Vivadent ExciTE F Single Dose Regular 0.1ml (759134)

Pack (50). ExciTE F is a light-curing, fluoride releasing, single- component total-etch adhesive. It is used in the  placement of direct restorations (composites,  compomers) as well as in the adhesive luting of  indirect restorations (all-ceramics, composites)  involving light-curing. ExciTE F is available in the  unique VivaPen, in bottles or in Soft Touch Single  Dose vessels. Advantages: Available in bottles and Soft Touch Single Dose vessels Reliable adhesion, as ExcitTE F establishes a strong bond to enamel and dentine Consistent quality due to its acetone-free chemistry Fluoride release Reduced postoperative sensitivity because dentin surfaces are effectively sealed Versatile system – Accurate fit of indirect restorations due to the low film thickness Indications: Direct light- and dual-cure composite and compomer restorations Adhesive luting of indirect restorations involving light-curing

Ivoclar Vivadent Tetric plus Fill Syringe 3g A2 plus

Each. Tetric plus Fill – handling tailored to your needs. More than 90% of the dentists rated the handling as "very good" or ""good" [1]: Sculptable viscosity that adapts well to cavity walls 92% of dentists reported high satisfaction with the cushioning effect [2] Viscosity can be adjusted by heating if desire Tetric plus meets all critieria essential for high-quality composites. 4 unique shades for easy shade matching With Tetric plus, 4 shades are sufficient to cover all VITA* classical shades and Bleach. The simplified universal composite offers esthetics that are suitable for all cavity classes. 4-filler technology for high-quality performance and proven handling Tetric plus matches conventional composites in every way - it meets all your requirements, including a handling process that receives 90 percent of dentists commend highly. [3] 4 mm for higher efficiency. 4 shades for greater simplicity. Tetric plus combines layer thicknesses of up to 4 mm [4] with a universal range of applications. Easy shade selection and consistent curing times facilitate your treatment workflow. In short: With Tetric plus, you can save time and money. *Not registered trademark of Ivoclar Vivadent AG. [1] [2] Internal study based on over 170 participants. [3] Internal study based on over 170 participants. More than 90 of participants rated the handling as “very good” or “good”. [4] Apply the shade A3.5 plus with a maximum layer thickness of 3.5 mm and light cure for 3s or 5s.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B1 (S) A14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT A3

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent Multilink Automix Refill Trans Easy 615216

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT B1

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT BL3

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 C16/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3 B40/3

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max ZirCAD CER/inLab LT A2 C17/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B2 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C2 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A1 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A2 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3.5 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B4 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C4 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D2 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D3 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A1 B40L/3

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A1 I12/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A2 I12/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A2 C14L/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 I12/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A2 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B2 C14/5

This is a clearance item and is only available at this one-off price while stocks last.

CLEARANCE - Ivoclar Vivadent Heliobond Refill 11g (532906AN) - Each

This is a clearance item and is only available at this one-off price while stocks last.

Ivoclar Vivadent Empress Direct Syringe Assortment (759177)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: with exceptionally high esthetic demands. who strive to mimic the appearance of natural teeth.  who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  Long working time.  High radiopacity.

Ivoclar Tetric Plus Fill: 1 x 3g Syringe - A3 Plus

Each.

Ivoclar Tetric Plus Fill: 1 x 3g Syringe - A3.5 Plus

Each.

Ivoclar Tetric Plus Fill: 1 x 3g Syringe - Bleach Plus

Each.

Ivoclar Tetric Plus Fill: 20 x 0.2g Cavifils - A2 Plus

Each.

Ivoclar Tetric Plus Fill: 20 x 0.2g Cavifils - A3 Plus

Each.

Ivoclar Tetric Plus Fill: 20 x 0.2g Cavifils - A3.5 Plus

Each.

Ivoclar Tetric Plus Fill: 20 x 0.2g Cavifils - Bleach Plus

Each.

Ivoclar Tetric Plus Flow: 1 x 2g Syringe - A2 Plus

Each.

Ivoclar Tetric Plus Flow: 1 x 2g Syringe - A3 Plus

Each.

Ivoclar Tetric Plus Flow: 1 x 2g Syringe - A3.5 Plus

Each.

Ivoclar Tetric Plus Flow: 1 x 2g Syringe - Bleach Plus

Each.

Ivoclar Tetric Plus Flow: 20 x 0.2g Cavifils - A2 Plus

Each.

Ivoclar Tetric Plus Flow: 20 x 0.2g Cavifils - A3 Plus

Each.

Ivoclar Tetric Plus Flow: 20 x 0.2g Cavifils - A3.5 Plus

Each.

Ivoclar Tetric Plus Flow: 20 x 0.2g Cavifils - Bleach Plus

Each.

Ivoclar Vivadent Variolink Esthetic LC Neutral 2g (763424)

Ivoclar Vivadent Monobond Etch&Prime Refill 5g (673026)

Each. Etch and prime in one easy step Monobond Etch & Prime is the first single-component ceramic primer in the world, which allows you to etch and silanate glass-ceramic surfaces in one easy step. At the same time, the solution cleans away any remaining saliva from the surface. Advantages Etching with hydrofluoric acid is unnecessary as all glass-ceramics are etched Short process requiring only one bottle - etches and silanates glass-ceramic in one easy step Long-lasting, stable bond due to the new ceramic conditioning and silanating system Indications Pre-treatment of glass-ceramic surfaces prior to the adhesive luting procedure with luting composites.

Ivoclar Vivadent OptraSculpt Refill Pointed Tip (683100AN)

OptraSculpt® are contouring instruments suitable for the non-stick shaping and contouring of surfaces. They are especially designed to shape unpolymerized sculptable composites in direct restorative treatments and to contour and smoothen paste-like laboratory composites.   The contouring and shaping of state-of-the-art high-quality dental composites is a challenging task. Thanks to their non-stick coating, the OptraSculpt attachments provide remedy since no instrument marks are left on the material.   Pointed Tip - For professional contouring of fissures.

Ivoclar Vivadent IPS Empress CAD CEREC Size C14 Multi A3.5

Pack (5)   Suitable for the fabrication of all-ceramic inlays, onlays, veneers, and crowns by means of CAD/CAM. They are available in two levels of translucency (high and low) as well as a polychromatic IPS Empress CAD Multi Block. IPS Empress CAD restorations are finally either only polished or stained and glazed, and adhesively cemented.   Multi Blocks – Lifelike transition of shade, translucency and fluorescence. Indications: anterior and posterior crowns, partial crowns & veneers.

Ivoclar Vivadent IPS Empress CAD CEREC Size C14 LT B1

Pack (5)   Suitable for the fabrication of all-ceramic inlays, onlays, veneers, and crowns by means of CAD/CAM. They are available in two levels of translucency (high and low) as well as a polychromatic IPS Empress CAD Multi Block. IPS Empress CAD restorations are finally either only polished or stained and glazed, and adhesively cemented.   LT Blocks – lower translucency and chameleon effect. Higher brightness value. Indications: anterior and posterior crowns, partial crowns and veneers.

Ivoclar Vivadent IPS Empress CAD CEREC Size C14 LT B2

Pack (5)   Suitable for the fabrication of all-ceramic inlays, onlays, veneers, and crowns by means of CAD/CAM. They are available in two levels of translucency (high and low) as well as a polychromatic IPS Empress CAD Multi Block. IPS Empress CAD restorations are finally either only polished or stained and glazed, and adhesively cemented.   LT Blocks – lower translucency and chameleon effect. Higher brightness value. Indications: anterior and posterior crowns, partial crowns and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C16 LT A2

Pack (5)   IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO).   The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns.   Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent Adhese Universal Vivapen 3.0 Kit - Each

Adhese Universal is a single-component, light-cured adhesive for direct and indirect bonding procedures. It is the only universal bonding agent available in the efficient VivaPen delivery form.   Universally suitable for direct and indirect bonding procedures and all etching protocols Consistent high bond strength (> 25 MPa) on wet and dry dentine Integrated desensitising effect for minimising the risk of postoperative sensitivity Efficient VivaPen: up to three times more applications per ml compared with conventional bottles Kit contains:   1 x 2ml Adhese Universal VivaPen 100 x VivaPen snap-on cannulas 20 x VivaPen protective sleeves

Ivoclar Vivadent IPS Empress Direct Flow Opal Refill 1.8g

The flowable variant of the IPS Empress Direct range of light-curing nano-hybrid composites. Both consistencies are based on the same tried-and-tested chemistry. With the three new IPS Empress Direct Flow materials, the desired esthetic effects can be created with high precision when anterior teeth are restored.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab A14 LT A3.5 (S)/5

Ivoclar Vivadent IPS Empress Direct Syringe Refill Dentin C3

Ivoclar Vivadent Tetric PowerFill Syringe IVW (668115WW) -3g

Ivoclar Vivadent IPS Empress Direct Color White 1g (637899)

Ivoclar Empress Direct B2 Enamel 10x0.2g Capsules (627276)

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3.5 (S) A16/5

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3.5 B32/3

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3 (S) A14/5

Pack (5).678866IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO).The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns.VeneersPartial crownsCrownsBridgesHybrid abutment crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3 B32/3

Pack (3). 648206IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO).The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns.VeneersPartial crownsCrownsBridgesHybrid abutment crowns

Ivoclar Vivadent Skyce Tooth Jewellery 2.4mm Large (559322)

Pack (5).The tooth jewels Skyce can simply be bonded to the tooth surface without preparation using tried-and-tested materials. Skyce is putting an extra sparkle into every smile. The crystal glass stones are available in two different sizes: Ø 1.9 mm and Ø 2.4 mm.Indications:-To be bonded to the labial surfaces of upper anterior teethAdvantages:-Bonding without preparationTried-and-tested materials are usedOral health is maintainedBenefits for the practice team:-You recommend a tried-and-tested system to your patientsThe professional solution for stylish tooth jewelleryExtension of the services your surgery offers

Ivoclar Vivadent Skyce Tooth Jewellery 1.9mm Small (559321)

Pack (5).The tooth jewels Skyce can simply be bonded to the tooth surface without preparation using tried-and-tested materials. Skyce is putting an extra sparkle into every smile. The crystal glass stones are available in two different sizes: Ø 1.9 mm and Ø 2.4 mm.Indications:-To be bonded to the labial surfaces of upper anterior teethAdvantages:-Bonding without preparationTried-and-tested materials are usedOral health is maintainedBenefits for the practice team:-You recommend a tried-and-tested system to your patientsThe professional solution for stylish tooth jewelleryExtension of the services your surgery offers

Ivoclar Empress Direct A3.5 Enamel 10x0.2g Capsules (627273)

Pack (10).IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region.For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:With exceptionally high esthetic demands.Who specialize in placing highly esthetic composite restorations. Who strive to mimic the appearance of natural teeth. Who value the wide range of shades and various levels of translucency offered  by the system. Advantages:Wide range of indications for anterior and posterior teeth. 32 shades and 5 levels of translucency. New opalescent shade. No need to use a specific layering technique. High surface gloss. Excellent polishing properties. Lifelike fluorescence associated with Empress materials. Autoclavable, non-fading ceramic shade guide. High insensitivity to light. Good radiopacity.

Ivoclar Tetric PowerFlow IVA Syringe 2g - Each

Each.Tetric PowerFlow is a flowable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -As initial layer / first increment in Class I and II composite restorations in permanent posterior teethRestoration of deciduous teeth.Advantages -EstheticsLifelike esthetics in the posterior regionIvocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.QualityIncreased process reliability thanks to fewer layersFewer errors thanks to short curing times starting from 3 secondsEfficiencyTime savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shadesA: Universal A shadeB: Universal B shadeW: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlow

Ivoclar Vivadent Tetric PowerFlow IVB Syringe 2g (692410)

Each.Tetric PowerFlow is a flowable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -As initial layer / first increment in Class I and II composite restorations in permanent posterior teethRestoration of deciduous teeth.Advantages -EstheticsLifelike esthetics in the posterior regionIvocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.QualityIncreased process reliability thanks to fewer layersFewer errors thanks to short curing times starting from 3 secondsEfficiencyTime savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shadesA: Universal A shadeB: Universal B shadeW: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlow

Ivoclar Vivadent Tetric PowerFlow IVW Syringe 2g (692411)

Each.Tetric PowerFlow is a flowable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -As initial layer / first increment in Class I and II composite restorations in permanent posterior teethRestoration of deciduous teeth.Advantages -EstheticsLifelike esthetics in the posterior regionIvocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.QualityIncreased process reliability thanks to fewer layersFewer errors thanks to short curing times starting from 3 secondsEfficiencyTime savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shadesA: Universal A shadeB: Universal B shadeW: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlow

Ivoclar Vivadent Tetric PowerFlow IVA Caps 20x0.2g (692413)

Pack (20).Tetric PowerFlow is a flowable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -As initial layer / first increment in Class I and II composite restorations in permanent posterior teethRestoration of deciduous teeth.Advantages -EstheticsLifelike esthetics in the posterior regionIvocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.QualityIncreased process reliability thanks to fewer layersFewer errors thanks to short curing times starting from 3 secondsEfficiencyTime savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shadesA: Universal A shadeB: Universal B shadeW: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlow

Ivoclar Vivadent Tetric PowerFlow IVB Caps 20x0.2g (692414)

Pack (20).Tetric PowerFlow is a flowable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -As initial layer / first increment in Class I and II composite restorations in permanent posterior teethRestoration of deciduous teeth.Advantages -EstheticsLifelike esthetics in the posterior regionIvocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.QualityIncreased process reliability thanks to fewer layersFewer errors thanks to short curing times starting from 3 secondsEfficiencyTime savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shadesA: Universal A shadeB: Universal B shadeW: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlow

Ivoclar Vivadent Tetric PowerFlow IVW Caps 20x0.2g (692415)

Pack (20).Tetric PowerFlow is a flowable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -As initial layer / first increment in Class I and II composite restorations in permanent posterior teethRestoration of deciduous teeth.Advantages -EstheticsLifelike esthetics in the posterior regionIvocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.QualityIncreased process reliability thanks to fewer layersFewer errors thanks to short curing times starting from 3 secondsEfficiencyTime savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shadesA: Universal A shadeB: Universal B shadeW: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlow

Ivoclar Vivadent Empress Direct Shade Guide Enamel (627215)

Each.IPS Empress Direct

Ivoclar Vivadent Tetric PowerFill IVA Syringe 3g (668083)

Each.Tetric Powerfill is a sculpable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -•Restorations in the posterior region (Class I and II, including the replacement of individual cusps)•Class V restorations (cervical caries, root erosion, wedge-shaped defects)•Reconstructive build-ups•Restoration of deciduous teeth.Advantages -Esthetics•Lifelike esthetics in the posterior region•Ivocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.Quality•Increased process reliability thanks to fewer layers•Fewer errors thanks to short curing times starting from 3 secondsEfficiency•Time savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shades•A: Universal A shade•B: Universal B shade•W: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlowSyringe

Ivoclar Vivadent Tetric PowerFill IVA Cavifil 0.2g (668107)

Pack (20).Tetric Powerfill is a sculpable, light-curing, radiopaque 4-mm composite for direct restorative treatments in posterior teeth. It offers short curing times starting from 3 seconds.Available in three enamel-like shades A, B and W.Indications -•Restorations in the posterior region (Class I and II, including the replacement of individual cusps)•Class V restorations (cervical caries, root erosion, wedge-shaped defects)•Reconstructive build-ups•Restoration of deciduous teeth.Advantages -Esthetics•Lifelike esthetics in the posterior region•Ivocerin and the Aessencio technology allow you to achieve the same high esthetics as with conventional composites.Quality•Increased process reliability thanks to fewer layers•Fewer errors thanks to short curing times starting from 3 secondsEfficiency•Time savings of up to 57% in the posterior region comapred to the conventional technique*Shades- Three enamel-like shades•A: Universal A shade•B: Universal B shade•W: White or light-coloured permanent teeth*Compared with Tetric EvoCeram and Tetric EvoFlowCavifil 0.2g

Ivoclar Vivadent Variolink Esthetic Try-In Paste Warm 1.7g

Each.Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years.Advantages:•Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free.•Balanced and straightforward Effect shade system.•Lifelike fluorescence.•Easy, precise, excess removal.•Flexible, situational consistency - ideal combination of flowability and stability.•Impressive radiodiagnostics.Indications:•Variolink Esthetic LC - Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers). Only for restorations with a low material thickness of •Variolink Esthetic DC - Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges).Includes 5 Application Tips

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 (S) A16/5

Pack (5).644367IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO).The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns.VeneersPartial crownsCrownsBridgesHybrid abutment crowns

Ivoclar Vivadent Tetric EvoCeram Cavifil A2D (637356) Pack20

Pack (20).Tetric EvoCeram, the composite restorative offering a balanced combination of properties, now available in new packaging.The tried-and-tested colour coding system based on the A-D shade guide has been carried over to the new syringes and Cavifils. In addition, Tetric EvoCeram is now available in the shades A2 Dentin, B1 and D2.Tetric Evo Ceram is a light-curing, universal nano-hybrid composite for top quality standard restorations in the anterior and posterior region. Benefits:Polymerisation on demand (POD): A long working time, combined with a short curing time.Natural shade blend: Coordinated light refraction indexes of fillers, monomer matrix and nano-colour pigments. Proven clinical performance: 85,000,000 restorations have been placed worldwide.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 (S) A14/5

Pack (5).678784IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO).The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns.VeneersPartial crownsCrownsBridgesHybrid abutment crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B1 (S) A14/5

Pack (5).678868IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO).The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns.VeneersPartial crownsCrownsBridgesHybrid abutment crowns

Ivoclar Empress Direct B3 Enamel 10x0.2g Capsules (627277)

Pack (10).IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region.For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:With exceptionally high esthetic demands.Who specialize in placing highly esthetic composite restorations. Who strive to mimic the appearance of natural teeth. Who value the wide range of shades and various levels of translucency offered  by the system. Advantages:Wide range of indications for anterior and posterior teeth. 32 shades and 5 levels of translucency. New opalescent shade. No need to use a specific layering technique. High surface gloss. Excellent polishing properties. Lifelike fluorescence associated with Empress materials. Autoclavable, non-fading ceramic shade guide. High insensitivity to light. Good radiopacity.

Ivoclar Empress Direct A4 Dentin 10x0.2g Capsules (627261)

Pack (10).IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region.For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:With exceptionally high esthetic demands.Who specialize in placing highly esthetic composite restorations. Who strive to mimic the appearance of natural teeth. Who value the wide range of shades and various levels of translucency offered  by the system. Advantages:Wide range of indications for anterior and posterior teeth. 32 shades and 5 levels of translucency. New opalescent shade. No need to use a specific layering technique. High surface gloss. Excellent polishing properties. Lifelike fluorescence associated with Empress materials. Autoclavable, non-fading ceramic shade guide. High insensitivity to light. Good radiopacity.

Ivoclar Empress Direct C3 Dentin 10x0.2g Capsules (627266)

Pack (10).IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region.For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:With exceptionally high esthetic demands.Who specialize in placing highly esthetic composite restorations. Who strive to mimic the appearance of natural teeth. Who value the wide range of shades and various levels of translucency offered  by the system. Advantages:Wide range of indications for anterior and posterior teeth. 32 shades and 5 levels of translucency. New opalescent shade. No need to use a specific layering technique. High surface gloss. Excellent polishing properties. Lifelike fluorescence associated with Empress materials. Autoclavable, non-fading ceramic shade guide. High insensitivity to light. Good radiopacity.

Ivoclar Empress Direct D2 Dentin 10x0.2g Capsules (627267)

Pack (10).IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region.For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:With exceptionally high esthetic demands.Who specialize in placing highly esthetic composite restorations. Who strive to mimic the appearance of natural teeth. Who value the wide range of shades and various levels of translucency offered  by the system. Advantages:Wide range of indications for anterior and posterior teeth. 32 shades and 5 levels of translucency. New opalescent shade. No need to use a specific layering technique. High surface gloss. Excellent polishing properties. Lifelike fluorescence associated with Empress materials. Autoclavable, non-fading ceramic shade guide. High insensitivity to light. Good radiopacity.

Ivoclar Empress Direct BL-XL Dentin 3g Syringe (627231)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:- with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages:- Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Vivadent Multilink Hybrid Abutment HO 0 (647182)

Each. Multilink Hybrid Abutment is a self-curing luting composite. It is suitable for the permanent, extraoral cementation of ceramic and PMMA structures on titanium bases in the fabrication of hybrid abutments or hybrid abutment crowns. This results in: a permanent cementation due to high bond strength values optimum esthetics due to two available opacity levels easy handling due to the convenient Automix syringe Indication Extraoral, permanent cementation of ceramic structures on their base. Shades HO 0 MO 0

Ivoclar Empress Direct BL-L Dentin 10x0.2g Capsules 627268

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Empress Direct BL-XL Dentin 10x0.2g Capsules 627269

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A2 (S) A16/5

Pack (5). 644368 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns. Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A2 (S) A14/5

Pack (5). 678785 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns. Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab LT A1 C14/5

Pack (5). 602567 The tried-and-tested IPS Empress CAD leucite glass-ceramic combines the modern CAD/CAM processing technology with a high-performance all-ceramic material. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. HT/LT blocks. Always choose the correct block for your individual patient cases from the comprehensive range. IPS Empress CAD blocks are available in two translucency levels (HT and LT) and as polychromatic Multi blocks. They are available both in Chromascop shade groups and in A-D shades. Moreover, the IPS Empress CAD LT blocks are available in 4 light and modern Bleach shades (BL1-BL4). Multi blocks. The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and the E4D* Dentist System (D4D). Advantages Twenty years of clinical experience with more than 40 million seated restorations. Leucite glass-ceramic (160 MPa) for exceptional esthetics. Comprehensive shade and size range for every patient situation. Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient. Polishing with OptraFine – no glazing necessary. Indications: Veneers, inlays, onlays, anterior and posterior crowns.

Ivoclar Empress Direct BL-XL Enamel 3g Syringe (627247)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Empress Direct BL-L Enamel 3g Syringe (627246)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Vivadent IPS e.max ZirCAD CER/in.MT Mul. A2 B45/3

Pack (3). 694542 IPS e.max ZirCAD involves a quick sintering process, which allows monolithic and esthetically pleasing zirconia restorations to be created directly in the dental practice using an efficient procedure. This makes this popular restorative material also suitable for chairside applications. IPS e.max ZirCAD is known for its high flexural strength (1,200 MPa*) and fracture toughness. It allows the fabrication of restorations with considerably lower wall thicknesses (posterior crowns: minimum 0.6 mm; anterior crowns: minimum 0.4 mm). Preparations preserve tooth structure and restorations can be cemented conventionally. Glazing is achieved with IPS e.max CAD Crystall./Glaze, which is available in two versions, one with fluorescent effect and one without. Processing Options Once sintered, the restorations can either be: glazed and fired stained (optional), glazed and fired polished Indications:- Crowns Three-unit bridges Your Benefits:- Chairside zirconia restorations allow practices to expand their portfolio of offerings Pleasing esthetics combined with high strength Tooth-preserving preparation and conventional cementation No risk of chipping Biocompatibility (*Average biaxial flexural strength. Ivoclar Vivadent AG, Schaan, Liechtenstein) The LT blocks are monochromatic, pre-shaded and are available in 7 A–D shades (A1, A2, A3, B1, B2, C2, D2) as well as 1 Bleach (BL) shade and in block sizes C17 and B45.

Ivoclar Vivadent IPS e.max ZirCAD CER/inLab LT A2 C17/5

Pack (5). 686194 IPS e.max ZirCAD involves a quick sintering process, which allows monolithic and esthetically pleasing zirconia restorations to be created directly in the dental practice using an efficient procedure. This makes this popular restorative material also suitable for chairside applications. IPS e.max ZirCAD is known for its high flexural strength (1,200 MPa*) and fracture toughness. It allows the fabrication of restorations with considerably lower wall thicknesses (posterior crowns: minimum 0.6 mm; anterior crowns: minimum 0.4 mm). Preparations preserve tooth structure and restorations can be cemented conventionally. Glazing is achieved with IPS e.max CAD Crystall./Glaze, which is available in two versions, one with fluorescent effect and one without. Processing Options Once sintered, the restorations can either be: glazed and fired stained (optional), glazed and fired polished Indications:- Crowns Three-unit bridges Your Benefits:- Chairside zirconia restorations allow practices to expand their portfolio of offerings Pleasing esthetics combined with high strength Tooth-preserving preparation and conventional cementation No risk of chipping Biocompatibility (*Average biaxial flexural strength. Ivoclar Vivadent AG, Schaan, Liechtenstein) The LT blocks are monochromatic, pre-shaded and are available in 7 A–D shades (A1, A2, A3, B1, B2, C2, D2) as well as 1 Bleach (BL) shade and in block sizes C17 and B45.

Ivoclar Vivadent IPS Empress CAD CEREC/inLab HT A2 I12/5

Pack (5). 602521 Suitable for the fabrication of all-ceramic inlays, onlays, veneers, and crowns by means of CAD/CAM. They are available in two levels of translucency (high and low) as well as a polychromatic IPS Empress CAD Multi Block. IPS Empress CAD restorations are finally either only polished or stained and glazed, and adhesively cemented.HT Blocks – higher translucency and chameleon effect. Lower brightness values. Indications: inlays, onlays and veneers.

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi BL1 C14L

Pack (5). 607672 IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa.  Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance.  IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi BL1 C14/5

Pack (5). 607683 IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa.  Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance.  IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi BL3 C14/5

Pack (5). 607684 IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa.  Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance.  IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi BL3 C14L

Pack (5). 607673 IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa.  Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance.  IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 C16/5

Pack (5). 648188 IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A2 B40/3

Pack (3). 634587 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3 B40/3

Pack (3). 634588 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT BL3

Pack (5). 680033 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT B1

Pack (5). 680031 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT BL2

Pack (5). 680032 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT BL4

Pack (5). 680034 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab LT A3 I12/5

Pack (5). 602559 Suitable for the fabrication of all-ceramic inlays, onlays, veneers, and crowns by means of CAD/CAM. They are available in two levels of translucency (high and low) as well as a polychromatic IPS Empress CAD Multi Block. IPS Empress CAD restorations are finally either only polished or stained and glazed, and adhesively cemented. LT Blocks – lower translucency and chameleon effect. Higher brightness value. Indications: anterior and posterior crowns, partial crowns and veneers.

Ivoclar Vivadent IPS Empress CAD CEREC/inLab LT A3.5 I12/5

Pack (5). 602560 Suitable for the fabrication of all-ceramic inlays, onlays, veneers, and crowns by means of CAD/CAM. They are available in two levels of translucency (high and low) as well as a polychromatic IPS Empress CAD Multi Block. IPS Empress CAD restorations are finally either only polished or stained and glazed, and adhesively cemented. LT Blocks – lower translucency and chameleon effect. Higher brightness value. Indications: anterior and posterior crowns, partial crowns and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3 (L) A16/5

Pack (5). 644386 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns. Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A2 (L) A16/5

Pack (5). 644385 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns. Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent OptraSculpt Refill Ball (683068) - Pack60

Pack (60). OptraSculpt® are contouring instruments suitable for the non-stick shaping and contouring of surfaces. They are especially designed to shape unpolymerized sculptable composites in direct restorative treatments and to contour and smoothen paste-like laboratory composites. The contouring and shaping of state-of-the-art high-quality dental composites is a challenging task. Thanks to their non-stick coating, the OptraSculpt attachments provide remedy since no instrument marks are left on the material. Ball - For adaption of composites.

Ivoclar Vivadent Bluephase G4 100-240V Grey (691258) - Each

Each. Intelligent LED light – carefree curing Patented Polyvision technology is your personal assistant when it comes to curing dental materials. This automatic assistance system helps you achieve reliable curing results. The curing light automatically detects movement of the handpiece during the light-curing procedure. It alerts the user of the improper operation by vibrating and automatically extends the exposure time by 10 per cent, if necessary. If the movement may prevent the material from curing properly, the light will automatically interrupt the exposure cycle so that it can be repeated. Bluephase G4 comes with active anti-glare protection to prevent the light from being activated in open space. Additional advantages: Reliable curing performance  for all light-curing materials due to polywave LED Short curing times starting from 10 seconds due to a high intensity of 1,200 mW/cm2 Wide 10-mm light guide for time-saving single-exposure curing procedures Additional Pre-Cure program for the removal of excess cement Delivery forms 691258 Bluephase G4 691257 Bluephase G4 with Click & Cure and integrated radiometer

Ivoclar Vivadent Bluephase G4 100-240V Grey & Radiometer

Each. Intelligent LED light – carefree curing Patented Polyvision technology is your personal assistant when it comes to curing dental materials. This automatic assistance system helps you achieve reliable curing results. The curing light automatically detects movement of the handpiece during the light-curing procedure. It alerts the user of the improper operation by vibrating and automatically extends the exposure time by 10 per cent, if necessary. If the movement may prevent the material from curing properly, the light will automatically interrupt the exposure cycle so that it can be repeated. Bluephase G4 comes with active anti-glare protection to prevent the light from being activated in open space. Additional advantages: Reliable curing performance  for all light-curing materials due to polywave LED Short curing times starting from 10 seconds due to a high intensity of 1,200 mW/cm2 Wide 10-mm light guide for time-saving single-exposure curing procedures Additional Pre-Cure program for the removal of excess cement Delivery forms 691258 Bluephase G4 691257 Bluephase G4 with Click & Cure and integrated radiometer

Ivoclar Vivadent Bluephase Powercure 100-240V (667092) -Each

Each. Product Features- 3sCure Program: Light intensity of 3,000 mW/cm² for curing times starting from 3 seconds Turbo Program: Light Intensity of 2,000 mW/cm² for curing times starting from 5 seconds High Power program: Light intensity of 1,200 mW/cm² for curing times starting from 10 seconds Cordless design for ultimate mobility in the dental office Intuitive handling with 2-button operation Inductive charging of the battery, no contaminated charging contacts Charging base with information of the charging status High-performance lithium ion battery for an operating capacity of 20 min. within the High Power program Light guide: shortened and autoclavable 3-year warranty (battery 1 year) Homogeneous light emission performance Backlit display for optimized hygiene Radiometer integrated in the charging base Optional corded operation with "Click & Cure"

Ivoclar Vivadent Ivoclean Refill 5g (637568) - Each

Each. The universal cleaning paste Ivoclean effectively cleans the bonding surfaces of prosthetic restorations after intraoral try-in and thus creates optimum pre-requisites for the adhesive luting procedure. Advantages:- Effective cleaning Universal – for all restorative materials Easy-to-use application Indication:- Extraoral cleaning of pre-treated ceramic and metal restoration surfaces which have been contaminated during intraoral try-in.

Ivoclar Empress Direct BL-L Dentin 3g Syringe (627230)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists:- with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages:- Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Empress Direct BL-XL Enamel 10x0.2g Capsules 627285

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Vivadent OptraStick Refill (699972) - Pack48

Pack (48). OptraStick is a placement instrument that features a flexible adhesive tip. The tip allows restorations and small objects of all kinds to be picked up, held, carried and placed quickly and easily. OptraStick is suitable for handling inlays, onlays, crowns and veneers made of a variety of materials, for example, IPS Empress, IPS e.max, IPS d.SIGN, IPS InLine and SR Adoro, as well as for metal restorations and tooth jewels, e.g. Skyce. Advantages Easy pick up Precise adherence Secure positioning

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT A1

Pack (5). IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 B32/3

Pack (3). 648204 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A2 B32/3

Pack (3). 648205 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B1 B32/3

Pack (3). 648209 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C1 B32/3

Pack (3). 648213 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D2 B32/3

Pack (3). 648217 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT BL2 B40L/3

Pack (3). 648957 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A1 B40L/3

Pack (3). 648870 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A2 B40L/3

Pack (3). 648871 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3 B40L/3

Pack (3). 648942 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3.5 B40L/3

Pack (3). 648943 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B1 B40L/3

Pack (3). 648945 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B2 B40L/3

Pack (3). 648946 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C1 B40L/3

Pack (3). 648949 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C2 B40L/3

Pack (3). 648950 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D2 B40L/3

Pack (3). 648953 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT BL1 C14/5

Pack (5). 626427 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT BL2 C14/5

Pack (5). 626428 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT BL3 C14/5

Pack (5). 626429 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT BL4 C14/5

Pack (5). 626430 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT A2

Pack (5). IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab Size C14 MT A3

Pack (5). IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The MT blocks are available in the shades A1, A2, A3, B1, BL2, BL3 and BL4. These medium- translucency blocks are used in cases where a brighter look is needed than that imparted by HT blocks and more translucency than with LT blocks. Due to the ideal balance of brightness and translucency, MT blocks are ideally suitable for the fabrication of anterior restorations. Customization is achieved by means of the staining or cut-back technique. Thin veneers and occlusal veneers Veneers Partial crowns Crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A3 C14/5

Pack (5). 602600 IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa.  Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance.  IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT BL1 C14/5

Pack (5). 605343 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns. Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT BL2 C14/5

Pack (5). 605344 IPS e.max is a high strength (360 MPa) lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). Its indication spectrum includes inlays/onlays, thin veneers, occlusal veneers, crowns, anterior/premolar bidges, implant superstructures as well as hybrid abutments and hybrid abutment crowns. In the fabrication of long-span bridges - also for the posterior region - IPS e.max CAD veneering structures are used in combination with zirconium oxide frameworks. IPS e.max CAD blocks are available in four levels of translucency (HT, MT, LT MO). The LT blocks are available in 16 A-D and 4 Bleach BL shades. Their low translucency – similar to that of natural dentin – renders these blocks suitable for creating large restorations (e.g. posterior crowns). The material exhibits true-to-nature brightness and chroma, which prevents the restoration from looking grey. The esthetic appearance of the restoration is maximized with the cut-back technique. The abutment blocks with a prefabricated connection are used for the creation of hybrid abutments and hybrid abutment crowns. Veneers Partial crowns Crowns Bridges Hybrid abutment crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A3 I12/5

Pack (5). 602594 IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa.  Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance.  IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Empress Direct BL-L Enamel 10x0.2g Capsules (627284)

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Empress Direct B1 Enamel 10x0.2g Capsules (627275)

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Empress Direct B1 Dentin 10x0.2g Capsules (627264)

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C3 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C4 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D2 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D3 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D4 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3.5 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A4 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B2 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B3 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B4 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C1 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C2 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C3 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C4 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D2 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D3 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D4 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3.5 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A4 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B3 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B4 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C1 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C4 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D2 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D3 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT D4 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A1 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A2 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3.5 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A4 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B1 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B2 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B3 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B4 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C1 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C2 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C3 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C4 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D2 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D3 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT D4 I12/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A1 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A2 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A3.5 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT A4 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B3 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT B4 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C1 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab HT C2 C14/5

Pack (5). IPS e.max CAD HT (High Translucency). High strength lithium disilicate glass-ceramic (LS2) for the CAD/CAM technique directly in the dental office (chairside) or the laboratory (labside). HT blocks - used for the milling of minimally-invasive, fully anatomical restorations, such as inlays, onlays and veneers.

Ivoclar Vivadent OptraSculpt Pad Refill 6mm (639793AN) Pk60

Pack (60). OptraSculpt Pad is a contouring instrument with special foam pad attachments, which is designed for the efficient, non-stick forming and shaping of composites. The highly flexible synthetic foam pads optimally adjust to the anatomical contours and allow a smooth modelling, without leaving any unwanted marks. The reference scales on the instrument handle assist in the creation of esthetic and anatomically-correct restorations. Advantages:- The non-stick surface of the foam pad attachments prevents the adhesion of composite resins. The instrument does not leave any marks and therefore ensures the creation of even surfaces. The reference scales on the instrument handle ensure professional esthetic results. Indications:- Suitable for adapting, shaping and contouring uncured packable composite and compomer materials in Class III, IV and V restorations and direct laminate veneers.

Ivoclar Vivadent Tetric EvoFlow Syringe B1 2g (641358) -Each

Each. Tetric EvoFlow is the nano-optimized flowable composite from Ivoclar Vivadent.  Tetric EvoFlow is characterized by optimum surface affinity. It even penetrates into areas that are difficult to reach. Therefore, it is suitable as an initial layer under medium-viscosity composites, such as Tetric EvoCeram. At the same time, however, Tetric EvoFlow is stable if required and thus ideally suitable for Class V restorations. The material can also be used for extended fissure sealing and the adhesive cementation of restorations.  Tetric EvoFlow is available both in Luer Lock syringes and Cavifils with a particularly thin tip.

Ivoclar Empress Direct C3 Enamel 10x0.2g Capsules (627281)

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Empress Direct D2 Enamel 10x0.2g Capsules (627282)

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites.  IPS Empress Direct is designed for dentists: With exceptionally high esthetic demands. Who specialize in placing highly esthetic composite restorations.  Who strive to mimic the appearance of natural teeth.  Who value the wide range of shades and various levels of translucency offered  by the system.  Advantages: Wide range of indications for anterior and posterior teeth.  32 shades and 5 levels of translucency.  New opalescent shade.  No need to use a specific layering technique.  High surface gloss.  Excellent polishing properties.  Lifelike fluorescence associated with Empress materials.  Autoclavable, non-fading ceramic shade guide.  High insensitivity to light.  Good radiopacity.

Ivoclar Vivadent Variolink Esthetic DC Light+ 5g (666117)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Light 5g (666118)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Neutral 5g (666119)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Warm 5g (666120)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Warm+ 5g (666121)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Light 9g (666122)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Neutral 9g (666123)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Variolink Esthetic DC Warm 9g (666124)

Each. Amazingly simple esthetics! Variolink Esthetic is an esthetic light- and dual-curing luting composite for the permanent cementation of demanding ceramic and composite restorations. The cement is based on the esthetic luting composites Variolink II and Variolink Veneer, which have proven their worth in clinical use for many years. Variolink Esthetic represents a new generation of luting composites featuring excellent esthetics and user-friendly processing. Advantages:- Excellent shade stability thanks to the patented and reactive light initiator Ivocerin which is 100% amine-free Balanced and straightforward Effect shade system Lifelike fluorescence Easy, precise excess removal Flexible, situational consistency – ideal combination of flowability and stability Impressive radiodiagnostics. Indication:- Variolink Esthetic LC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays and veneers) Only for restorations with a low material thickness of Variolink Esthetic DC Permanent cementation of glass-ceramic, lithium disilicate glass-ceramic and composite restorations (inlays, onlays, partial crowns, crowns, bridges)

Ivoclar Vivadent Tetric EvoFlow Cavifil B1 20x0.2g (641348)

Pack (20). Tetric EvoFlow is based on the proven chemical formula of Tetric Ceram, however it provides a lighter viscosity which allows the material to flow into difficult to reach areas. Its high radiopacity, compressive strength and shade selection make it ideal as the initial layer of any restoration, as well as, cervical restorations.  High radiopacity and fluoride release. Longer working time.  Cavity wall adaptation without instruments. Small restorations filled without air bubbles.  Convenient and accurate application with cavifil delivery.  Twelve available shades, cavifil and syringe delivery.

Ivoclar Empress Direct B1 Dentin 3g Syringe (627226) - Each

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Empress Direct A3.5 Enamel 3g Syringe (627235)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Empress Direct B1 Enamel 3g Syringe (627237) - Each

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

Ivoclar Empress Direct A3.5 Dentin 3g Syringe (627624)

Each. IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists with exceptionally high esthetic demands who specialize in placing highly esthetic composite restorations who strive to mimic the appearance of natural teeth who value the wide range of shades and various levels of translucency offered  by the system Advantages Wide range of indications for anterior and posterior teeth 32 shades and 5 levels of translucency New opalescent shade No need to use a specific layering technique High surface gloss Excellent polishing properties Lifelike fluorescence associated with Empress materials Autoclavable, non-fading ceramic shade guide High insensitivity to light Good radiopacity

*Ivoclar SpeedCEM Plus Refill Transparent 9g - Each

*this product is temperature controlled, and therefore is not able to be returned for credit. Please store this product in the fridge between 2-8°C* Each. 681712. Contains 1 Automix syringe SpeedCEM Plus transparent 9g, 15 Mixing tips, 5 Root canal tips SpeedCEM Plus is a self-adhesive, selfcuring resin cement with optional lightcuring. SpeedCEM Plus offers an ideal combination of performance and user-friendliness. Its formulation has been optimized to make it particularly suitable for use in conjunction with restorations made of zirconium oxide and metal-ceramics and for the cementation of restorations on implant abutments. Advantages Excellent self-cure performance ideal for zirconia and metal-ceramics User-friendly handling Easy clean-up High Radiopacity Tolerant processing Efficient process with just one component Indications SpeedCEM Plus is suited for the permanent seating of crowns and bridges on natural teeth and on implant abutments that are made of the following restorative materials: Oxide ceramics such as zirconium oxide, e.g. Zenostar or IPS e.max ZirCAD Metal and metal-based restorations Lithium disilicate glass-ceramics, e.g. IPS e.max Available shades: Transparent, Opaque, Yellow

*Ivoclar Vivadent SpeedCEM Plus Refill Opaque 9g - Each

*this product is temperature controlled, and therefore is not able to be returned for credit. Please store this product in the fridge between 2-8°C* Each. 681711. Contains 1 Automix syringe SpeedCEM Plus opaque 9g, 15 Mixing tips, 5 Root canal tips SpeedCEM Plus is a self-adhesive, selfcuring resin cement with optional lightcuring. SpeedCEM Plus offers an ideal combination of performance and user-friendliness. Its formulation has been optimized to make it particularly suitable for use in conjunction with restorations made of zirconium oxide and metal-ceramics and for the cementation of restorations on implant abutments. Advantages Excellent self-cure performance ideal for zirconia and metal-ceramics User-friendly handling Easy clean-up High Radiopacity Tolerant processing Efficient process with just one component Indications SpeedCEM Plus is suited for the permanent seating of crowns and bridges on natural teeth and on implant abutments that are made of the following restorative materials: Oxide ceramics such as zirconium oxide, e.g. Zenostar or IPS e.max ZirCAD Metal and metal-based restorations Lithium disilicate glass-ceramics, e.g. IPS e.max Available shades: Transparent, Opaque, Yellow

Ivoclar Vivadent SpeedCEM Plus Refill Yellow 9g - Each

Each. 681710. Contains 1 Automix syringe SpeedCEM Plus yellow 9g, 15 Mixing tips, 5 Root canal tips SpeedCEM Plus is a self-adhesive, selfcuring resin cement with optional lightcuring. SpeedCEM Plus offers an ideal combination of performance and user-friendliness. Its formulation has been optimized to make it particularly suitable for use in conjunction with restorations made of zirconium oxide and metal-ceramics and for the cementation of restorations on implant abutments. Advantages Excellent self-cure performance ideal for zirconia and metal-ceramics User-friendly handling Easy clean-up High Radiopacity Tolerant processing Efficient process with just one component Indications SpeedCEM Plus is suited for the permanent seating of crowns and bridges on natural teeth and on implant abutments that are made of the following restorative materials: Oxide ceramics such as zirconium oxide, e.g. Zenostar or IPS e.max ZirCAD Metal and metal-based restorations Lithium disilicate glass-ceramics, e.g. IPS e.max Available shades: Transparent, Opaque, Yellow

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A2 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B1 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A1 I12/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent Variolink Esthetic Try-In Paste Light+ 1.7g

Each. 666067   Variolink® Esthetic try-in pastes are water-soluble glycerine pastes. The try-in pastes enable the shade effect of all-ceramic restorations (veneers, inlays, onlays, crowns and bridges) to be simulated which are to be cemented with Variolink Esthetic luting composite. Please note that the shade and translucency of the try-in pastes correspond to that of the cured (!) Variolink Esthetic luting composite. The shade of the try-in pastes slightly deviates from that of the respective uncured luting composite, as the luting composite only obtains its final shade after curing. The shade effect of the try-in pastes is coordinated with that of the fully cured luting composite of the same thickness. The Variolink Esthetic try-in pastes contain glycerine, mineral fillers and dyes.

Ivoclar Vivadent Variolink Esthetic Try-In Paste Light 1.7g

Each. 666113   Variolink® Esthetic try-in pastes are water-soluble glycerine pastes. The try-in pastes enable the shade effect of all-ceramic restorations (veneers, inlays, onlays, crowns and bridges) to be simulated which are to be cemented with Variolink Esthetic luting composite. Please note that the shade and translucency of the try-in pastes correspond to that of the cured (!) Variolink Esthetic luting composite. The shade of the try-in pastes slightly deviates from that of the respective uncured luting composite, as the luting composite only obtains its final shade after curing. The shade effect of the try-in pastes is coordinated with that of the fully cured luting composite of the same thickness. The Variolink Esthetic try-in pastes contain glycerine, mineral fillers and dyes.

Ivoclar Vivadent Variolink Esthetic TryIn Paste Neutral 1.7g

Each. 666114   Variolink® Esthetic try-in pastes are water-soluble glycerine pastes. The try-in pastes enable the shade effect of all-ceramic restorations (veneers, inlays, onlays, crowns and bridges) to be simulated which are to be cemented with Variolink Esthetic luting composite. Please note that the shade and translucency of the try-in pastes correspond to that of the cured (!) Variolink Esthetic luting composite. The shade of the try-in pastes slightly deviates from that of the respective uncured luting composite, as the luting composite only obtains its final shade after curing. The shade effect of the try-in pastes is coordinated with that of the fully cured luting composite of the same thickness. The Variolink Esthetic try-in pastes contain glycerine, mineral fillers and dyes.

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A2 I12/5

Pack (5). 602593. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A1 C14/5

Pack (5). 602598. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A2 C14/5

Pack (5). 602599. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A1 C14L/5

Pack (5). 602604. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A2 C14L/5

Pack (5). 602605. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent IPS Empress CAD CEREC/inLab Multi A1 I12/5

Pack (5). 602592. IPS Empress CAD is excellently suitable for the fabrication of highly esthetic monochromatic single-tooth restorations, such as veneers, inlays, onlays, anterior and posterior crowns. With its homogeneity and light scattering behaviour, IPS Empress provides a balanced chameleon effect. In addition of the light-optical properties, IPS Empress CAD restorations are distinguished for their lifelike translucency, high esthetics, and a flexural strength of 160 MPa. Multi blocks The innovative polychromatic IPS Empress CAD Multi Blocks result in restorations which are distinguished for a true-to-nature shade and fluorescence transition from dentin to incisal, even without characterization. They thus provide maximum esthetics and true-to-nature appearance. IPS Empress CAD blocks can be milled in both theCEREC* System (Sirona) and Chairside CAD/CAM system from Planmeca. Advantages Twenty years of clinical experience with more than 40 million seated restorations Leucite glass-ceramic (160 MPa) for exceptional esthetics Comprehensive shade and size range for every patient situation Choice of true-to-nature chameleon effect, lifelike brightness value or natural shade gradient Polishing with OptraFine – no glazing necessary Indications Veneers, inlays, onlays, anterior and posterior crowns

Ivoclar Vivadent Liquid Strip 2.5g (532505AN) - Each

Each. Glycerine gel to prevent the oxygen-inhibited layer of composites with composite or ceramic restorations. Indications Try-in paste Preventing an inhibited layer with composites Protecting the etching pattern of lab-fabricated all-ceramic restorations

Ivoclar Vivadent Programat CS3 Furnace (681117) - Each

Each. Programat CS3 Power cord Vacuum hose Programat firing tray kit Automatic temperature checking set ATK 2 (test set) USB download cable Programat USB flash drive Programat WLAN kit Firing tong holder DSA Holder kit A–D shade guide. Power supply 100 V, 50 – 60 Hz 110 – 120 V, 50 – 60 Hz 200 – 240 V, 50 – 60 Hz Admissible voltage fluctuations ±10 % Max. power consumption 14 A at 100 V 12 A at 110 – 120 V 8.5 A at 200 – 240 V Data for vacuum pump Max. power consumption: 250 W / max. leakage current 0.75 mA Final vacuum: < 50 mbar Only tested pumps can be used. Dimensions of Depth: 465 mm closed furnace Width: 320 mm / 390 mm (with cooling tray) Height: 320 mm Usable size Diameter: 90 mm of the firing chamber Height: 80 mm Max. firing temperature 1,200 °C Weight Base: 15.6 kg

Ivoclar Empress Direct A3.5 Dentin 10x0.2g Capsules (627623)

Pack (10). IPS Empress Direct is a light-curing, highly esthetic nano-hybrid composite filling material for direct restorative procedures in the anterior and posterior region. For nearly 20 years, the name IPS Empress has been associated with the highest level of esthetics in the reproduction of natural tooth characteristics. IPS Empress Direct from the IPS Empress range combines the esthetics of ceramics with the application advantages of composites. IPS Empress Direct is designed for dentists: with exceptionally high esthetic demands. who specialize in placing highly esthetic composite restorations. who strive to mimic the appearance of natural teeth. who value the wide range of shades and various levels of translucency offered by the system. Advantages: Wide range of indications for anterior and posterior teeth. 32 shades and 5 levels of translucency. New opalescent shade. No need to use a specific layering technique. High surface gloss. Excellent polishing properties. Lifelike fluorescence associated with Empress materials. Autoclavable, non-fading ceramic shade guide. High insensitivity to light. Good radiopacity.

Ivoclar Vivadent OptraSculpt Pad Refill 4mm (639792AN) Pk60

Pack (60). OptraSculpt Pad is a contouring instrument with special foam pad attachments, which is designed for the efficient, non-stick forming and shaping of composites. The highly flexible synthetic foam pads optimally adjust to the anatomical contours and allow a smooth modelling, without leaving any unwanted marks. The reference scales on the instrument handle assist in the creation of esthetic and anatomically-correct restorations. Advantages:- The non-stick surface of the foam pad attachments prevents the adhesion of composite resins. The instrument does not leave any marks and therefore ensures the creation of even surfaces. The reference scales on the instrument handle ensure professional esthetic results. Indications:- Suitable for adapting, shaping and contouring uncured packable composite and compomer materials in Class III, IV and V restorations and direct laminate veneers.

Ivoclar Vivadent Tetric EvoCeram Syringe B1 3g (637547WW)

Each Tetric EvoCeram is the universal composite for anterior and posterior restorations that affords outstanding esthetics. The filler technology employed in Tetric EvoCeram is based on an optimum blend of different fillers and filler sizes.

Ivoclar Vivadent Tetric EvoCeram Cavifil B1 20x0.2g (637354)

Pack (20) Tetric EvoCeram is the universal composite for anterior and posterior restorations that affords outstanding esthetics. The filler technology employed in Tetric EvoCeram is based on an optimum blend of different fillers and filler sizes. Advantages Universal nano-hybrid composite for anterior and posterior restorations Proven clinical performance with over 100 million restorations placed worldwide More working time due to the patented light sensitivity filter Natural shade blend with surrounding dentition ensures outstanding restorative results

Ivoclar Vivadent Adhese Universal VivaPen Refill 2ml - Each

Each. Adhese Universal is a single-component, light-cured adhesive for direct and indirect bonding procedures that features compatibility with all etching techniques: self-etch, selective-enamel-etch and total-etch. Adhese Universal is available in the unique VivaPen delivery form for fast and convenient direct intra-oral application with minimal waste to optimize cost-effectiveness. Indications: Direct-placed light-curing composite and compomer restorations. Core build-ups with light-, self- and dual-curing composites. Adhesive cementation of indirect restorations with light and dual-curing luting composites. Intraoral repair of fractured composite and compomer restorations. Desensitization of hypersensitive cervical areas. Sealing of prepared tooth surfaces before temporary / permanent cementation of indirect restorations. Advantages: Efficient delivery – up to 190 single-tooth applications per 2ml VivaPen* Universal application – for all bonding and etching techniques Predictable results – high bond strength on dentin and enamel

Ivoclar Vivadent OptraSculpt Pad Instrument Refill (759593)

Each. Composite Sculpting and Modelling Instrument

Ivoclar Vivadent Empress Direct Syringe Opaque 1.8g (637897)

Each. Indications:- Masking of – Exposed metal surfaces when repairing defective ceramic and composite veneers intraorally; – Discoloration on teeth . Advantages:- – Due to IPS Empress Direct Opaque’s outstanding masking ability, the application of a thin layer is sufficient to effectively cover up unsightly stains and metal surfaces.

Ivoclar Vivadent OptraSculpt Pad Kit (765560AN)

Each . OptraSculpt Pad is a contouring instrument with special foam pad attachments, which is designed for the efficient, non-stick forming and shaping of composites. The highly flexible synthetic foam pads optimally adjust to the anatomical contours and allow a smooth modelling, without leaving any unwanted marks. The reference scales on the instrument handle assist in the creation of esthetic and anatomically-correct restorations. Advantages:- The non-stick surface of the foam pad attachments prevents the adhesion of composite resins. The instrument does not leave any marks and therefore ensures the creation of even surfaces. The reference scales on the instrument handle ensure professional esthetic results. Indications:- Suitable for adapting, shaping and contouring uncured packable composite and compomer materials in Class III, IV and V restorations and direct laminate veneers.

Ivoclar Vivadent VivaStyle PaintOn Plus Patient Kit (602873)

****PLEASE NOTE THAT IF YOUR PURCHASING THIS PRODUCT WITHIN THE EUROPEAN UNION, IT CAN ONLY BE PURCHASED BY A REGISTERED DENTIST****.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT A3 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B1 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT B2 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C2 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT C3 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT BL3 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.

Ivoclar Vivadent IPS e.max CAD CEREC/inLab LT BL4 C14/5

Pack (5). IPS e.max CAD LT (Low Translucency). The blocks are available in 9 A-D, 4 Bleach BL shades and in 2 different sizes (I12, C14). Due to their translucency, they are ideal for fabricating restorations in the staining and cut-back technique. Shading is based on the tried-and-tested shades of IPS Empress CAD LT. The blocks are shaded according to the tooth shade. Thus, staining and veneering is reduced to a minimum.